Avaya Bogen Universal Paging Access Module Uživatelský manuál

Universal Paging Access ModuleInstallation and Use Manual© 1999 Bogen Communications, Inc.All rights reserved. 54-2003-01 9910LUUPAM: PEC Code: 5335-

Trunk Port Connections - Loop Start (cont'd)Figure 2: Trunk Port Connection: Loop Start Trunk Port[10]

[11]Specific InstructionsTrunk Port Connections - Ground Start NOTE: Controls for VOX DELAY, PAGING TIME, MODE Switch S5 and AUX switchesS1, S2, S3, a

Trunk Port Connections - Ground Start (cont'd)9.Connect UPAM +24/48V terminal to PBX ground.NOTE:Usually the AC GND terminal on the included 48-v

[13]Specific InstructionsStation Port / Centrex ConnectionsDisconnect Methods In station port operation, the UPAM provides CPC (calling-party-controll

[14]Station Port / Centrex Connections (cont’d)5. Connect "Tip" of station port to T terminal of UPAM (see Figure 5).6. Connect "Ring&q

Station Port/Centrex Connections (cont'd)Important Centrex SettingsSome phone systems (in particular, Centrex-type systems) may produce open-swit

Station Port/Centrex Connections (cont'd)Inhibit Default TimerChanging Default Timer RangeRing DelayAn option is available to inhibit the default

[17]Specific InstructionsTrunk Port Connections - Page Port NOTE: Controls for VOX DELAY, PAGING TIME, MODE Switch S5 and AUX switchesS1, S2, S3, and

Trunk Port Connections - Page Port (cont'd)7.Connect PT and PR terminals and contact closure on UPAM to the paging system,as shown in Section 3.

[19]3. Connection to the Paging SystemGeneral GuidelinesThe UPAM is designed to connect to typical central-amplified and self-amplifiedpaging and soun

© 1999 Bogen Communications, Inc.All Rights Reserved. Printed in U.S.A.NoticeEvery effort was made to ensure that the information inthis guide was com

[20]Connecting the UPAM to an Amplifier's Lo-Z/600-ohm Input (cont’d)1. Make sure that the amplifier is turned off or unplugged. 2. Connect one s

Connecting the UPAM to an Amplifier’s Lo-Z/600-ohm Input (cont'd)Figure 7. Typical Connection to a Lo-Z/600-ohm Input[21]

[22]Typical Installation: Connecting the UPAM to an Amplifier’sHi-Z AUX InputYou can connect the UPAM to an amplifier's Hi-Z input by using the L

Connecting the UPAM to an Amplifier's Hi-Z AUX Input (cont'd)Figure 8. Typical Connection to a Hi-Z Input[23]

[24]Typical Installation: Connecting the UPAM to an Amplifier’sMIC InputDue to the higher sensitivity of Hi-Z microphone inputs, they should be used o

Connecting the UPAM to an Amplifier's MIC Input (cont'd)Figure 9. Typical Connection to a MIC Input[25]

[26]Typical Installation: Connecting the UPAM to a Self-AmplifiedPaging SystemConnection to a self-amplified system usually consists of connecting the

Connecting the UPAM to a Self-amplified Paging System (cont'd)Figure 10. Typical Connection to a Self-Amplified Paging System[27]

Functional Test GuideUse the following chart to verify proper operation after installation. To start the test,pick up a telephone and call the UPAM.[2

Procedure A1.Disconnect the UPAM from the telephone equipment.2.Confirm that the power supply is properly connected and that the MODE switches are int

[3]Contents1. Product Identification...5UPAM Universal Paging Access Mo

Troubleshooting (cont'd)Procedure B1.2.3.4.Disconnect the UPAM from the paging system.Connect a test set to PT & PR terminals on UPAM (see Fi

[4]This page left blank intentionally.

1.Product IdentificationUPAM Universal Paging Access ModuleThe UPAM Universal Paging Access Module is designed to provide telephoneaccess to most comm

[6]Features24V or 48V Operation MODE switches let you select 24V (not included) or 48V (included)(Trunk Port Operation) power supply. A 48-volt power

[7]2. Connection to the TelephoneSystemGeneral InstructionsOverview This section contains installation procedures for connection to the telephone syst

[8]General Instructions (cont’d)MODE Switches (on front of unit) A set of 5 MODE switches (S1 through S5, see Figure 1 on page 5) is included toset th

[9]Specific InstructionsTrunk Port Connections - Loop Start NOTE: Controls for VOX DELAY, PAGING TIME, MODE Switch S5 and AUX switchesS1, S2, S3, and