Avaya EE Networking Uživatelská příručka stáhnout pdf (Strana 24)

24 Using Enterprise Edge Services

Enterprise Edge Networking Operations Guide P0910464 Issue 01

Static Routing

Enterprise Edge users can add static routes to the IP routing table. These static

routes take precedence over those routes chosen by routing protocols, such as RIP.

To add a static route, see Static Route on page 94.

Note: Ensure that users do not add a static route for default route 0.0.0.0 with mask

0.0.0.0. Enterprise Edge’s Net Link Manager automatically creates a default

route and adjusts it according to link status unless router or Net Link

Manager are running.

Routing Information Protocol (RIP)

RIP is a widely-used protocol for managing routing information in a self-contained

network such as a corporate intranet. RIP is classified by the Internet Engineering

Task Force (IETF) as one of several internal gateway protocols (IGPs).

A RIP router sends full updates, which list all the other hosts it knows about, to its

closest neighbor host every 30 seconds. The neighbor host sends the information to

its next neighbor, until all the hosts in the network know the routing paths, a state

known as network convergence. RIP uses a hop count to determine network

distance. Each host with a router in the network uses the routing table information

to determine the next host for the packet, until a specified destination is reached.

Enabling RIP on Network Interfaces

To run RIP on one or more network interfaces, go to the specific interface under

router and enable RIP. After you enable RIP for an interface, you do not have to

reboot the Enterprise Edge server for the changes to take effect.

Packet Filtering

A packet is a unit of data routed between an origin and a destination on the Internet

or on any other packet-switched network. When any file such as an e-mail message,

HTML file, GIF file or URL request, is sent on the Internet, the IP layer divides the

file into packets of an efficient size for routing. Each of these packets is numbered

and includes the Internet address of the destination.

Enterprise Edge supports basic (or stateless) packet filtering for IP. You can

configure the filter to pass only the packets from the routes they list, or to pass

everything except the packets for the routes they list.

Each route in the list can be any combination of the following packet filtering

features. By default, no packet filer is configured.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 181 182

Žádné komentáře

marque: Dayton | Catégorie: Space heaters | Taille: 0.35 MB |

Dayton Propane

Construction Heater

Model 3VG80

Repair Parts List

Plus de produits et de manuels pour Chauffages d'appoint Dayton

Modèles	Type de document
3VE53H	Instructions d'exploitation Dayton 3VE53H Operating instructions, 18 pages
2E510D	Instructions d'exploitation Dayton 2E510D Operating instructions, 16 pages
3E134E	Guide de dépannage Dayton 3E134E Troubleshooting guide, 24 pages
6BY70	Instructions d'exploitation Dayton 6BY70 Operating instructions, 16 pages
7D837A	Guide de dépannage Dayton 7D837A Troubleshooting guide, 40 pages
3E358B	Instructions d'exploitation Dayton 3E358B Operating instructions, 24 pages
1RVT8	Guide de dépannage Dayton 1RVT8 Troubleshooting guide, 24 pages
1VNW9A	Instructions d'exploitation Dayton 1VNW9A Operating instructions, 12 pages
4E769B	Instructions d'exploitation Dayton 4E769B Operating instructions, 16 pages
3	Manuel de l'utilisateur O&M Manual IA, DIA - Joyce/Dayton Corp., 13 pages
1UCR1	Manuel de l'utilisateur BULLDOGS, 20 pages
7E259	Manuel de l'utilisateur Chronic Disease Self.. - Community Health Centers of Greater Dayton, 1 pages
1UCP8	Spécifications Dayton 1UCP8 Specifications, 64 pages