Avaya Configuring Frame Relay Services Uživatelský manuál Strana 215
- Strana / 240
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Monitoring Frame Relay Using BCC show Commands
117376-C Rev. 00
C-7
vcs [-dlci
<dlci>
] [-interface
<name>
] [-service
<name>
]
[-type {pvc
|
dynamic-pvc
|
svc}] [-state {active
|
inactive
|
invalid
|
xoff
|
control
|
starting}]
Displays information about all those frame relay VCs with the specified DLCI.
This command allows for the following command filters and filter arguments:
-dlci
<dlci>
Displays only frame relay VCs with the specified
DLCI.
-interface
<name>
Displays only frame relay interfaces configured
on the specified interface.
-service
<name>
Displays only frame relay VCs on the specified
service record.
-type
{
pvc | dynamic-pvc | svc
}
Displays information about only those VCs of
type:
•
pvc
-- shows only frame relay VCs that are
statically configured PVCs
.
•
dynamic-pvc
-- shows only frame relay VCs
that are dynamically learned PVCs.
•
svc
-- shows only frame relay VCs that are
SVCs.
-state
{active | inactive | invalid |
xoff | control | starting}
Displays information about only those VCs in
one of the following states:
•
Invalid
-- VC is configured but the switch has
not confirmed it.
•
Active
-- VC is usable.
•
Inactive
-- VC is configured but not active.
•
xoff
-- VCs are XOFF’d.
•
control --
shows only control VCs
•
starting
--
shows VCs that are starting
- Configuring 1
- Frame Relay Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117376-C Rev. 00 10
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 26
- Configuring an SVC 27
- Chapter 2 31
- Frame Relay Overview 31
- Introduction to Frame Relay 32
- Permanent Virtual Circuits 33
- Switched Virtual Circuits 33
- PVC and SVC Comparison 34
- Frame Relay Packets 35
- . Note, however 36
- Management Protocols 37
- BYS0037A 38
- LAPF Operational States 39
- SVC Signaling 41
- Call Setup 42
- Message Processing 43
- Frame Relay Service Records 44
- Frame Relay Access Modes 45
- Direct Access Mode 46
- Hybrid Access Mode 46
- Source Routing 48
- RFC 1490 48
- Address Resolution for PVCs 48
- Address Resolution for SVCs 49
- Traffic Control 50
- Data Compression 51
- Data Encryption 51
- Protocol Prioritization 51
- Traffic Shaping 53
- Quality of Service 55
- Traffic Shaping for SVCs 57
- Incoming 59
- Outgoing 59
- CIR Configuration Guidelines 60
- WCP and CIR Enforcement 60
- Oversubscribing the Interface 62
- X.213 Priority for SVCs 64
- Inactivity Timing for SVCs 64
- Multiline for PVCs 65
- PVC Pass-Through 67
- Frame Relay Dial Services 68
- Caution: 71
- Selecting a Management Type 72
- Selecting a DLCI Address Type 74
- Selecting Address Length 74
- Monitoring the Connection 76
- Polling Interval 77
- Full Enquiry Interval 77
- Customizing PVCs 81
- To delete PVCs: 87
- To move PVCs: 87
- Enabling Multicast 88
- Configuring PVC Pass-Through 90
- <integer> 100
- Enabling Compression for PVCs 102
- Using the BCC 103
- Using Site Manager 103
- Customizing SVCs 105
- For example: 107
- To delete service records: 107
- Call Screening and Blocking 108
- Disabling SVCs 112
- Disconnecting Active SVCs 114
- Setup Timer 121
- <value> 126
- (continued) 128
- Congestion Control 129
- Congestion Timer 130
- Congestion Counter 130
- Congestion Method 131
- To enable congestion control 134
- To enable traffic shaping 139
- To disable compression: 141
- To set X.213 priority value 143
- Deleting Frame Relay 144
- Customizing Frame Relay 145
- Appendix A 147
- Site Manager Parameters 147
- Figure A-2 148
- SVC LAPF Parameters 157
- SVC Signaling Parameters 163
- Parameters for PVCs 168
- PVC Service Record Parameters 172
- SVC Service Record Parameters 180
- SVC Options Parameters 186
- WHERE DOES THIS PARAMETER GO? 200
- Appendix B 201
- Table B-1. RIP Parameters 202
- Appendix C 209
- Monitoring Frame Relay Using 209
- BCC show Commands 209
- Commands for Frame Relay 210
- <option> 212
- <dlci> 215
- <name> 215
- ] [-service 216
- <multiline_name> 223
- <name> 228
Související produkty a manuály pro Sítě Avaya Configuring Frame Relay Services
Sítě Avaya BCM 2.5 Uživatelská příručka
(50 stránky)
(50 stránky)
Sítě Avaya Glossary of Media Processing Server Series Terminology (Software Release 2.1) Uživatelský manuál
(124 stránky)
(124 stránky)
Sítě Avaya BayRS Version 15.2.0.0 Oznámení
(68 stránky)
(68 stránky)
Sítě Avaya Configuring DLSw Services Uživatelský manuál
(204 stránky)
(204 stránky)
Sítě Avaya BCM200/400 Instalační manuál
(386 stránky)
(386 stránky)
Sítě Avaya X.25 Uživatelský manuál
(198 stránky)
(198 stránky)
Sítě Avaya Configuring OSI Services Uživatelský manuál
(148 stránky)
(148 stránky)
Sítě Avaya BCM450 Průvodce konfigurací
(11 stránky)
(11 stránky)
Sítě Avaya X.25 Uživatelský manuál
(50 stránky)
(50 stránky)
Sítě Avaya BayRS Version 15.1.0.0 Oznámení
(72 stránky)
(72 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce