Avaya 3100 Mobile Communicator Deployment Uživatelská příručka Strana 74
- Strana / 172
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
7. At the prompt for the mode, do one of the following:
• If the Avaya 3100 Mobile Communicator Gateway configuration is not
redundant, select Standalone mode.
• If the Avaya 3100 Mobile Communicator Gateway configuration is redundant,
select Active-Standby mode, and go to
8 on page 74.
8. For Active-Standby mode, at the prompt, enter the following information:
• Server name: the domain name (if defined) or the internal IP address of the
primary Avaya 3100 Mobile Communicator Gateway. This value is the same
for both the primary and secondary Avaya 3100 Mobile Communicator
Gateway servers.
• Cluster name: this value is not currently in use. Use the default value.
• Partner IP address: the IP address of the other Avaya 3100 Mobile
Communicator Gateway server.
9. Select Finish to save the configuration.
10. Remove the CD.
11. For a redundant configuration, repeat this procedure on the other server.
Commissioning
This section describes the Avaya 3100 Mobile Communicator Gateway commissioning.
After completing the commissioning, you configure the system security, configure the client
services, install the clients, and back up the Avaya 3100 Mobile Communicator Gateway
database. For more information, see Avaya 3100 Mobile Communicator Administration and
Security, NN42030-600
After you configure the Avaya 3100 Mobile Communicator solution, you configure the Avaya
3100 Mobile Communicator to interwork with the appropriate communication server, using the
appropriate Solution Integration Guide.
Adding an Avaya 3100 Mobile Communicator Gateway
server
Add the Avaya 3100 Mobile Communicator Gateway using the Avaya 3100 Mobile
Communicator Web Administration Console.
Avaya 3100 Mobile Communicator Gateway installation
74 Deployment Guide October 2010
- Deployment Guide 1
- Features 7
- Other changes 7
- New in this release 8
- Chapter 2: Introduction 9
- Introduction 10
- Planning and engineering 12
- Chapter 4: Planning 13
- Planning 14
- Security requirements 18
- High availability 20
- Capacity 22
- Chapter 5: Engineering 23
- Table 2: ECS ports 27
- Engineering 28
- Communicator 30
- Avaya CS 1000 and UDP 32
- Avaya CS 1000 with CDP 32
- SIP Trunk configuration 34
- Device Handoff configuration 35
- Trunk calculation: Method 1 38
- Trunk calculation: Method 2 39
- UEXT calculations 42
- Communicator features 42
- Call Detail Recording 44
- Direct outbound call 44
- Call-Me-First outbound call 44
- Incoming call 44
- Licensing requirements 48
- • Country Code 50
- • Area Code 50
- Parameter: Country Code 51
- Parameter: Area Code 51
- Mobility prefix 52
- Data access planning 53
- Service DN 53
- Universal Extensions 54
- Caller ID table 54
- Avaya 3100 MC - Client user 55
- Deployment planning 56
- Deployment work flow 58
- Communicator system baseline 59
- 1. Log on to Element Manager 61
- Deployment prerequisites 62
- Chapter 10: Avaya 3100 Mobile 63
- Preparation 65
- Installing the Linux base 67
- Installation 72
- Installation task flow 72
- Job aid: Admin shell access 73
- Commissioning 74
- Procedure job aid 76
- Rules that use the carat sign 82
- Figure 17: Gateway Actions 88
- Figure 18: System status tab 89
- Solution commissioning 92
- Configuring zones 97
- Configuring virtual routes 98
- Configuring virtual trunks 100
- Configuring ESN access codes 101
- Coordinated Dialing Plan 103
- Configuring a Handoff key 105
- Configuring a HOT P key 106
- 8. Verify the Local SIP Port 108
- 9. Type the SIP Domain Name 108
- Figure 25: SIP URI map 111
- Warm restart 112
- Cold restart 112
- Configuring NRS 112
- NRS Database 113
- Committing NRS Database 113
- Figure 28: Database switched 114
- Figure 29: Database committed 114
- Figure 30: NRS Server 115
- Figure 35: Gateway Endpoints 117
- Example: 3100MCG 118
- Adding a User Endpoint 119
- Figure 38: Add User Endpoint 120
- Figure 39: User Endpoints 121
- Communicator Gateway 122
- MWI for Avaya CS 1000 127
- CallPilot MWI configuration 128
- Validate deployment 130
- 1000 ECS deployment 132
- Navigation 135
- Upgrade work flow 136
- Release upgrade taskflow 137
- Prerequisites 140
- Upgrade fundamentals 146
- Upgrade commissioning 147
- Chapter 15: Maintenance 151
- Parameter Description 152
- Maintenance 152
- Chapter 16: Common procedures 155
- Variable definitions 156
- Administration Console 157
- Common procedures 158
- Linux base worksheet 163
- Table 19: Solution checklist 166
- Figure 53: Outgoing call flow 170
Související produkty a manuály pro ne Avaya 3100 Mobile Communicator Deployment
(12 stránky)
ne Avaya M3900 Instalační příručka
(3 stránky)
(3 stránky)
ne Avaya BCM Networking Uživatelská příručka
(8 stránky)
(8 stránky)
ne Avaya EE Networking Uživatelský manuál
(14 stránky)
(14 stránky)
ne Avaya 1145B2 Uživatelský manuál
(1 stránky)
(1 stránky)
ne Avaya 1120E Uživatelská příručka
(164 stránky)
(164 stránky)
ne Avaya BCC Rychlý návod
(4 stránky)
(4 stránky)
ne Avaya 20A Uživatelský manuál
(1 stránky)
(1 stránky)
ne Avaya 4620/4620SW Uživatelský manuál
(1 stránky)
ne Avaya 14.20_Rev Uživatelský manuál
(3 stránky)
(3 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce