Avaya Managing Routers and BNX Platforms Uživatelský manuál Strana 145
- Strana / 254
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Managing Router Files
114083 Rev. A 5-25
Modifying
config
Files in Remote Configuration Mode
Use this procedure when you use the Configuration Manager remote mode to
modify a config file.
1. Compact the contents of the memory card or flash SIMM if your router
is equipped with one.
See the next section, “Compacting File Space on a Memory Card or Flash
SIMM.”
2. Copy the config file to a new file named temp.
See “Copying a File” earlier in this chapter.
3. Modify temp, using the Configuration Manager remote mode.
Refer to the appropriate Bay Networks manual for customizing the type of
router software you use.
4. Save temp. When you save in remote mode, Site Manager automatically
copies the file to the router.
5. To test your modifications, boot the router with the file temp.
Refer to “Booting a Router” in Chapter 7.
6. Check the MIB version in the Site Manager main window. If the version
is earlier than 7.80, verify that
-- Adequate free space exists on the router’s diskette to copy temp to another
file
-- Adequate contiguous free space exists on the router’s memory card or
flash SIMM to copy temp to another file
7. Copy the file temp to config.
8. Boot the router with config.
9. Delete temp.
Note: Routers that run 7.80 (or later) software automatically verify the
existence of adequate free space on the destination volume specified in a file
copy operation.
- Managing Routers and 1
- BNX Platforms 1
- Bay Networks Software License 3
- Contents 5
- 114083 Rev. A vii 7
- 114083 Rev. A ix 9
- 114083 Rev. A 10
- 114083 Rev. A xi 11
- 114083 Rev. A xiii 13
- 114083 Rev. A xv 15
- 114083 Rev. A xvii 17
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- 114083 Rev. A xxv 25
- Bay Networks Customer Service 26
- World Wide Web 27
- Customer Service FTP 27
- Support Source CD 28
- CompuServe 28
- InfoFACTS 29
- How to Get Help 29
- Chapter 1 31
- Overview of Router Management 31
- Monitoring Traps and Events 32
- Viewing Trap Messages 33
- 1-4 114083 Rev. A 34
- Viewing Event Messages 36
- 1-8 114083 Rev. A 38
- Using the Quick Get Tool 40
- Using the Screen Builder Tool 41
- Using the Screen Manager Tool 41
- 1-14 114083 Rev. A 44
- Keeping a Log 47
- 1-18 114083 Rev. A 48
- Chapter 2 49
- Using the Trap Monitor 49
- 2-2 114083 Rev. A 50
- Managers 52
- (Figure 2-4) 52
- Saving a Configuration 53
- 2-6 114083 Rev. A 54
- 114083 Rev. A 2-7 55
- 2-8 114083 Rev. A 56
- 114083 Rev. A 2-9 57
- 2-10 114083 Rev. A 58
- 114083 Rev. A 2-11 59
- 2-12 114083 Rev. A 60
- 114083 Rev. A 2-13 61
- Field Value 61
- Enabling an SNMP Agent 62
- 114083 Rev. A 2-15 63
- Filtering Trap Messages 66
- 2-20 114083 Rev. A 68
- 3. Click on Save 68
- Saving Trap Messages 69
- Chapter 3 71
- Monitoring Router Events 71
- Displaying Event Logs 72
- Displaying a Remote Log 74
- Displaying a Local Log 75
- Filtering Event Messages 76
- Saving Event Messages 79
- Chapter 4 83
- Accessing Statistics 84
- Viewing the Bay Networks MIB 85
- 4-4 114083 Rev. A 86
- Using the MIB Browser 87
- 4-6 114083 Rev. A 88
- 4-8 114083 Rev. A 90
- 114083 Rev. A 4-9 91
- 114083 Rev. A 4-11 93
- Adding Statistics Screens 95
- Filename Screen description 96
- MAN0002A 96
- Removing Statistics Screens 97
- Displaying Statistics Screens 98
- 4-18 114083 Rev. A 100
- Monitoring Statistics 101
- 4-20 114083 Rev. A 102
- Creating Statistics Filters 103
- Using Display Filters 104
- Display Filter Example: 105
- 4-24 114083 Rev. A 106
- Using Retrieval Filters 107
- 4-26 114083 Rev. A 108
- 1. Select Search > Find 108
- Saving Statistics Information 109
- Designing Statistics Screens 110
- 114083 Rev. A 4-29 111
- 114083 Rev. A 4-31 113
- 2. Launch the screen 115
- 114083 Rev. A 4-35 117
- 4-36 114083 Rev. A 118
- Table 4-2. MIB II Counters 118
- For More Information 119
- Chapter 5 121
- Managing Router Files 121
- (Figure 5-1) 122
- Active Volumes 123
- 5-4 114083 Rev. A 124
- Default Filenames 125
- Connecting to a Router 126
- Naming a File 127
- Copying a File 128
- Verifying Adequate Free Space 129
- Creating the Copy 130
- Deleting a File 131
- Transferring a File 132
- Setting Up Multiple Routers 134
- 114083 Rev. A 5-15 135
- 4. Click on Save 137
- Getting a File 138
- 114083 Rev. A 5-19 139
- Putting a File 140
- 114083 Rev. A 5-23 143
- Modifying 145
- 5-26 114083 Rev. A 146
- 3. Click on OK 146
- Creating a Partition 148
- 114083 Rev. A 5-29 149
- Deleting a Partition 151
- Router Files Manager window: 152
- Chapter 6 153
- Using the Report Generator 153
- 6-2 114083 Rev. A 154
- (Figure 6-2) 155
- 114083 Rev. A 6-5 157
- 114083 Rev. A 6-7 159
- <version>.rpt. For 160
- <report file> 161
- (continued) 161
- (continued) 161
- 114083 Rev. A 6-11 163
- ROUTER=192.32.156.3 164
- FILE=/usr1/jb/southcape.adt 164
- EMAIL=pgrant,llantz,odiaz 164
- /usr1/jake/audit.cfg 165
- Chapter 7 167
- Booting a Router 168
- 114083 Rev. A 7-3 169
- Using Delayed Boot 170
- 114083 Rev. A 7-5 171
- 7-6 114083 Rev. A 172
- 2. Click on Add 172
- 114083 Rev. A 7-7 173
- 7-8 114083 Rev. A 174
- 4. Click on OK 174
- 114083 Rev. A 7-9 175
- 177
- LOCAL, PLUS, MINUS* 179
- Booting a Processor Module 180
- 114083 Rev. A 7-15 181
- Clearing the Event Log 182
- Pinging a Remote Device 183
- IP Ping Responses 185
- IPX Ping 186
- Figure 7-13. IPX Ping Window 187
- IPX Ping Responses 188
- OSI Ping 189
- OSI Ping Responses 190
- VINES Ping 191
- VINES Ping Responses 192
- AppleTalk Ping 193
- AppleTalk Ping Responses 195
- APPN Ping 195
- 7-30 114083 Rev. A 196
- Figure 7-17. APPN Ping Window 196
- APPN Ping Responses 197
- 7-32 114083 Rev. A 198
- Partitioning Overview 199
- Restart slot? 202
- Chapter 8 203
- Using the Ping MIB 203
- 8-2 114083 Rev. A 204
- Intervals > IP 206
- (Figure 8-4) 206
- Click on Add 207
- (Figure 8-5) 207
- 8-8 114083 Rev. A 210
- 211
- 212
- 212
- 213
- Specifying Source Routes 214
- 114083 Rev. A 8-13 215
- Reviewing IP Ping Statistics 216
- Appendix A 217
- Responding to SNMP SET Errors 217
- SNMP set error! 218
- Object wf SyncLineNumber 218
- UNIX Workstations 219
- DOS Workstations 219
- Appendix B 221
- Using the 221
- Facility 221
- Configuring the 222
- Understanding How 223
- Filters Messages 223
- Configuring 224
- Group Parameters 224
- B-6 114083 Rev. A 226
- Host List 227
- (Figure B-4) 228
- 114083 Rev. A B-9 229
- Using the syslog Facility 231
- B-12 114083 Rev. A 232
- B-14 114083 Rev. A 234
- B-16 114083 Rev. A 236
- Table B-1 236
- Error Levels 236
- Deleting the 240
- Facility from the Router 240
- Appendix C 241
- Using Config Generator 242
- Checking for Errors 243
- Checking MIB Attributes 243
- Checking MIB Attribute Values 244
- 114083 Rev. A Index-1 245
- 114083 Rev. A Index-3 247
- 114083 Rev. A Index-5 249
- 114083 Rev. A Index-7 251
- 114083 Rev. A Index-9 253
Související produkty a manuály pro Software Avaya Managing Routers and BNX Platforms
Software Avaya Configuring and Troubleshooting Bay Dial VPN (DVS) Networks Uživatelský manuál
(188 stránky)
(188 stránky)
Software Avaya CS1000 Uživatelský manuál
(180 stránky)
(180 stránky)
Software Avaya Business Communications Manager - Personal Call Manager Uživatelská příručka
(90 stránky)
(90 stránky)
Software Avaya v4.1 Uživatelský manuál
(166 stránky)
(166 stránky)
Software Avaya Business Communications Manager Release 6.0 - BCM-IVR Integration Supplement Uživatelský manuál
(36 stránky)
(36 stránky)
Software Avaya 4n(114973-A Oznámení
(60 stránky)
(60 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.215 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce