Avaya Configuring IP, ARP, RARP, RIP, and OSPF Services Uživatelský manuál Strana 231
- Strana / 390
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Customizing OSPF Services
308627-14.20 Rev 00
6-47
Configuring a Summary Route
OSPF border routers generate summary advertisements for their attached areas.
Each summary advertisement specifies a range of destinations in an area. An area
range specification consists of a network address and a variable-length mask.
For example, a summary advertisement for the destination 140.191.0.0 with a
mask of 255.255.0.0 describes a single route to the collection of destinations
140.191.0.0 through 140.191.255.255. A packet is always forwarded to the
network that is the best (longest or most specific) match for the packet’s
destination.
You can use the BCC or Site Manager to configure a summary route.
Using the BCC
To configure a summary route, go to an OSPF area prompt (for example,
box; ip;
ospf; area/0.0.0.2
) and enter:
summary network
<ip_address>
[
mask
<ip_mask>
]
ip_address
and
ip_mask
are an IP address/mask pair defining the summary route.
(If you do not explicitly configure the mask value, the natural address class mask
is configured.)
For example, the following command creates the summary route 140.191.0.0 with
a mask of 255.255.0.0:
area/0.0.0.1#
summary network 140.191.0.0 mask 255.255.0.0
summary/0.0.0.1/140.191.0.0#
By default, OSPF advertises the summary route. To change the setting, go
to the summary route prompt (for example,
box; ip; ospf; area/0.0.0.1;
summary/0.0.0.1/140.191.0.0
) and enter:
action
<action>
action
is one of the following:
advertise
(the default)
block
- Configuring IP, ARP, RARP 1
- RIP, and OSPF Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308627-14.20 Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Related Publications 21
- How to Get Help 22
- Chapter 1 23
- IP Addresses 24
- Subnet Addressing 26
- Supernet Addressing 29
- Autonomous Systems 30
- Figure 1-4. ARP Example 33
- OSPF Neighbors 37
- Neighbor Adjacencies 37
- Designated Routers 38
- AS External Routes 38
- OSPF Areas 39
- OSPF Router Types 41
- OSPF Implementation Notes 41
- Router Discovery Protocol 42
- Route Preferences 43
- Route Weights 44
- Figure 1-7. IP Routing Table 46
- IP Traffic Filters 50
- Chapter 2 51
- Starting IP Services 51
- Starting RIP 53
- Starting OSPF 54
- Starting Router Discovery 54
- Adding RIP to an IP Interface 57
- Starting RARP 59
- Chapter 3 61
- Setting the ICMP Error Limit 75
- Caution: 81
- Customizing an IP Interface 84
- Specifying a MAC Address 97
- IP0012A 99
- Using the BCC 100
- Using Site Manager 100
- Configuring an SMDS Address 102
- (continued) 103
- Deleting IP from an Interface 106
- Defining a Static Route 117
- (continued) 119
- Defining a Default Route 121
- Customizing Router Discovery 122
- Choosing a Broadcast Type 124
- Chapter 4 129
- Customizing ARP 130
- Customizing Global ARP 131
- Figure 4-1. Proxy ARP Example 137
- Customizing RARP 141
- Deleting RARP Globally 144
- Chapter 5 145
- Customizing RIP Services 145
- Setting the RIP Diameter 146
- Customizing a RIP Interface 147
- Selecting the RIP Version 148
- ) and enter: 149
- Specifying the Update Mode 153
- Sending Triggered Updates 155
- Receiving RIP Updates 158
- Listening for a Default Route 161
- Defining a RIP Accept Policy 170
- Chapter 6 185
- Customizing OSPF Services 185
- Supplying an OSPF Router ID 188
- Figure 6-1. OSPF ASE Routes 193
- Setting the Holddown Timer 198
- <value> 199
- <seconds> 199
- Configuring Message Logging 200
- Changing the Area ID 205
- Specifying the Interface Type 206
- Estimating the Transit Delay 210
- Setting the Hello Interval 212
- Setting the Dead Interval 214
- Specifying the Metric Cost 217
- Specifying the MTU Size 219
- Examples 223
- Configuring Areas 226
- Configuring Authentication 229
- Configuring a Summary Route 231
- Configuring a Stub Area 233
- Transit area 244
- Policies 257
- Appendix A 263
- Site Manager Parameters 263
- IP Parameters 264
- IP Interface Parameters 266
- IP Global Parameters 280
- Static Route Parameters 289
- Adjacent Host Parameters 292
- Router Discovery Parameters 295
- RARP Parameters 297
- OSPF Parameters 298
- OSPF Global Parameters 299
- OSPF Interface Parameters 303
- OSPF Area Parameters 311
- Area Range Parameters 315
- OSPF NSSA Range Parameters 318
- RIP Parameters 324
- Manager online Help 331
- RIP Accept Policy Parameters 335
- OSPF Accept Policy Parameters 337
- Appendix B 353
- RIP Import Filters 354
- RIP Export Filters 357
- OSPF Import Filters 360
- OSPF Export Filters 363
- Appendix C 367
- Route Weight Worksheet 367
- Appendix D 371
- IP/OSPF Configuration Example 371
- Manager and the BCC 374
Související produkty a manuály pro Software Avaya Configuring IP, ARP, RARP, RIP, and OSPF Services
Software Avaya BayRs Version 12.20 Uživatelský manuál
(218 stránky)
(218 stránky)
Software Avaya PeriReporter Business Communications Manager Release 6.0 Uživatelský manuál
(133 stránky)
(133 stránky)
Software Avaya CS1000 Uživatelský manuál
(180 stránky)
(180 stránky)
Software Avaya Digital Enchanced Cordless Telecommuncations SIP DECT Fundamentals Uživatelský manuál
(254 stránky)
(254 stránky)
Software Avaya Connecting BayStack AN and ANH Platforms to a Network Uživatelský manuál
(178 stránky)
(178 stránky)
Software Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Uživatelský manuál
(148 stránky)
(148 stránky)
Software Avaya Configuring Traffic Filters and Protocol Prioritization Uživatelský manuál
(162 stránky)
(162 stránky)
Software Avaya Nortel Business Communications Manager 450 1.0 Administration and Security Uživatelský manuál
(200 stránky)
(200 stránky)
Software Avaya BCM 4.0 Uživatelský manuál
(398 stránky)
(398 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.103 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce