Avaya Configuring Dial Services Uživatelský manuál Strana 168
- Strana / 258
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Configuring Dial Services
5-32
Circuit Options Parameters
Use the following descriptions as guidelines when you configure the circuit
options parameters.
Parameter: Circuit Type
Default: Normal
Options: Primary | Normal
Function: Specifies whether or not the circuit over the selected leased line uses the
dial backup service. These lines are not part of the backup pool. For a
normal, that is, standard leased circuit, the router does not provide a
backup if the original circuit fails. For a primary circuit, the router does
provide a backup to carry traffic.
Instructions: Accept the default, Normal, if you do not want a backup circuit for the
data going across this line. Select Primary if you want to use the dial
backup service.
MIB Object ID: 1.3.6.1.4.1.18.3.5.1.4.1.1.31
Parameter: Backup Pool ID
Default: None
Range: 1 to 255
Function: Identifies the backup pool for the primary circuit.
Instructions: If you select Primary in the Circuit Type parameter, enter the ID of the
backup line pool that this circuit should use. If you select Normal for the
Circuit Type parameter, Site Manager does not allow you to enter a
backup pool ID.
You must create a backup pool before you can specify a circuit as
primary. The router first creates the circuit as a normal circuit. See
Chapter 4 for instructions on creating a backup pool.
MIB Object ID: 1.3.6.1.4.1.18.3.5.1.4.5.1.5
- Configuring Dial Services 1
- Bay Networks Software License 3
- Contents 5
- About This Guide 19
- CompuServe 21
- InfoFACTS 22
- World Wide Web 22
- How to Get Help 23
- Conventions 23
- Acronyms 24
- Chapter 1 27
- Dial Services Overview 27
- Dial-on-Demand Service 29
- Demand Lines and Pools 30
- Activating Demand Circuits 32
- Dial Backup Service 34
- Backup Lines and Pools 36
- Activating the Backup Line 37
- Bandwidth-on-Demand Service 38
- Activating Secondary Lines 40
- Terminating Secondary Lines 40
- Chapter 2 43
- ISDN Overview 43
- ISDN Standards 44
- Primary Rate Interface 45
- The D Channel 45
- Figure 2-3. LAPD Frame 46
- ISDN Interfaces 47
- Reference Points 48
- Chapter 3 51
- Implementation Notes 51
- D Channel Support 52
- B Channel Support 52
- S/T Interfaces 53
- BRI Subaddresses 54
- Selective PRI Service 55
- Call Screening 56
- Rate Adaption 56
- Example 1 57
- Example 2 57
- Point-to-Point Protocol 58
- IP Adjacent Hosts 61
- Data Compression 62
- PPP Multilink 63
- Static Routes 64
- Protocol Prioritization 65
- Breath-of-Life Messages 67
- Bandwidth for Backup Circuits 68
- Chapter 4 79
- Using the MIB Object ID 80
- Configuring Line Pools 80
- Pool ID Parameter 86
- Line Media Type Parameters 86
- Adding Line Pools 87
- Configuring ISDN Lines 91
- PRI Physical Interfaces 93
- MCT1/MCE1 Clock Parameters 97
- MCT1/MCE1 Port Parameters 98
- MCT1 Port Parameters 100
- Creating Line Pools 101
- Configuring Dial Services 102
- MCE1 Port Parameters 105
- MCT1/MCE1 Logical Lines 108
- Logical Lines Parameter 111
- (continued) 113
- (continued) 114
- Configuring ISDN Logical Lines 116
- Logical Lines Parameters 118
- fills in the fields below it 121
- Local Phone Number Parameters 123
- Changing a Line Pool 127
- Changing Lines in a Pool 128
- Port Parameters 134
- Timeslots 134
- Chapter 5 137
- Configuring Circuits 137
- Interface for Dialup Lines 139
- Demand Circuit Parameters 140
- Configuring Circuits 141
- Click on Done 151
- Schedule Parameters 152
- Deleting Demand Circuits 155
- 4. Click on OK to save 157
- Providing Backup Circuits 164
- Click on OK 166
- Circuit Options Parameters 168
- Primary Circuit Parameters 169
- (Figure 5-19) 175
- (Figure 5-20) 176
- Manager window 176
- Deleting Backup Circuits 178
- Click on Done to exit 182
- Congestion Monitor Parameters 189
- (Figure 5-26) 194
- Chapter 6 197
- Configuring Phone Lists 197
- Configuring Phone Lists 199
- Chapter 7 209
- Caller Resolution Table 209
- (Figure 7-2) 210
- Appendix A 217
- Configuration Examples 217
- Dial-on-Demand Using PPP 218
- Demand Pools Configuration 219
- Demand Circuit Configuration 220
- Configuration Examples 221
- Configuration of Router 1 222
- Configuration of Router 2 223
- Demand Pool Configuration 224
- Outgoing Phone List 225
- Protocol Configuration 226
- Backup Circuit Configuration 230
- Backup Pool Configuration 235
- Type)➔Circuit Options window 236
- Appendix B 239
- Appendix C 247
Související produkty a manuály pro Software Avaya Configuring Dial Services
Software Avaya Configuring and Troubleshooting Bay Dial VPN (DVS) Networks Uživatelský manuál
(188 stránky)
(188 stránky)
Software Avaya CS1000 Uživatelský manuál
(180 stránky)
(180 stránky)
Software Avaya Business Communications Manager - Personal Call Manager Uživatelská příručka
(90 stránky)
(90 stránky)
Software Avaya v4.1 Uživatelský manuál
(166 stránky)
(166 stránky)
Software Avaya Business Communications Manager Release 6.0 - BCM-IVR Integration Supplement Uživatelský manuál
(36 stránky)
(36 stránky)
Software Avaya 4n(114973-A Oznámení
(60 stránky)
(60 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce