Avaya Business Communications Manager 50 Instalační manuál Strana 73
- Strana / 301
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 6 Checking the installation prerequisites 73
Installation and Maintenance Guide
Chapter 6
Checking the installation prerequisites
Before you install a main unit or expansion unit, perform the following tasks:
• Determine the location for the Avaya Business Communications Manager 50 (Avaya BCM50)
units, telephones, and other equipment based on space and electrical requirements.
• Order the required trunks from the central office.
• Ensure that you have all the equipment and supplies you need to install the system.
For information about Avaya BCM50 installation prerequisites:
• Environmental requirements on page 73
• Electrical requirements on page 73
• Site telephony wiring requirements on page 74
• System equipment, supplies, and tools on page 75
Environmental requirements
Ensure you meet the installation environmental requirements. The installation area must be:
• a minimum of 4 m (13 ft.) from equipment such as photocopiers, electrical motors, and other
equipment that produces electromagnetic, radio frequency, and electrostatic interference
• within 1.5 m (5 ft.) of a three-wire grounded electrical outlet
• clean, dry, well ventilated, and free of traffic and excess dust
• within the temperature range of 5°C and 50°C (40°F and 120°F)
• from 20% to 80% non condensing relative humidity
• structurally strong and with enough space to support the BCM50 units
• a minimum of 46 cm (18 in.) from the floor
Electrical requirements
Ensure you meet the following electrical requirements:
• Power must be supplied from a non switched, unobstructed outlet within 1.5 m (5 ft.) of the
Avaya BCM50 units.
• The supplied power must be a dedicated 110 V to 120 V AC nominal (or 220 V to 240 V AC
nominal), 50 to 60 Hz, 15 A minimum service with a third-wire safety ground. The third-wire
safety ground provides shock protection and prevents electromagnetic interference.
Note: The installation area must be of sufficient height from the floor to prevent water
damage.
- Installation and Maintenance 1
- Contents 3
- 10 Contents 10
- NN40170-305 10
- New in this release 11
- 12 New in this release 12
- Regulatory information 13
- EMI/EMC (FCC Part 15) 14
- Important safety instructions 14
- Regulatory information 15 15
- Use of a music source 16
- Enhanced 911 configuration 17
- Radio-frequency interference 17
- 18 Regulatory information 18
- Additional safety information 19
- 20 Regulatory information 20
- Chapter 1 21
- 22 Chapter 1 Getting started 22
- Symbols and text conventions 23
- Related publications 25
- Customer service 26
- Chapter 1 Getting started 27 27
- 28 Chapter 1 Getting started 28
- Chapter 2 29
- ports and connectors 31
- Media bay modules 37
- Trunk media bay modules 39
- Global Analog Trunk Module 40
- Station media bay modules 41
- 4x16 media bay module 42
- Avaya BCM50 hardware 46
- Patch panel 47
- Wall-mount bracket 47
- Wiring field card 48
- Avaya BCM50 components 49
- Uninterruptable power supply 50
- Hard disk 51
- Cooling fan 51
- RJ-21 telephony connector 52
- Field-replaceable units 53
- Accessories 54
- Chapter 3 55
- LAN port LEDs 57
- Figure 30 MBM LEDs 61
- DTM LEDs 62
- BRIM LEDs 63
- Chapter 4 65
- (with integrated router) 66
- Chapter 5 69
- Chapter 6 73
- Digital loop 74
- Analog loop 74
- Basic hardware 75
- Optional equipment 75
- Other hardware and tools 75
- Chapter 7 77
- Unpacking the main unit 78
- Slots Feet 81
- To install the patch panel 82
- To install the WFC 86
- Chapter 8 91
- Unpacking the expansion unit 93
- To set GASM dip switches 95
- To set GATM dip switches 96
- To install an MBM 97
- Chapter 9 99
- Connecting the expansion unit 100
- To connect an expansion unit 101
- Connecting the power supply 102
- Figure 51 Connect a UPS 103
- Wiring warnings 105
- G4x16/G8x16 108
- G8x16 MBMs 109
- Music source specifications 111
- Figure 52 Music source jack 112
- Next step 114
- Chapter 10 115
- Installing IP Deskphones 116
- Chapter 11 117
- Installing the ATA2 118
- To connect the ATA2 119
- Mounting the ATA2 119
- To mount the ATA2 on a wall 119
- Figure 57 ATA2 back view 120
- Mounting keyhole slots 120
- Configuring the ATA2 121
- Chapter 12 123
- Initial parameters overview 124
- Startup parameters overview 125
- Chapter 13 127
- To enter the keycodes 128
- To configure the IP address 129
- To configure the modem 129
- To select the region 130
- To initialize voice mail 130
- Chapter 14 133
- Prerequisites 135
- To enter a keycode 136
- To configure IP Deskphones 141
- To configure SNMP settings 142
- To create user accounts 143
- Chapter 15 145
- Startup Profile requirements 146
- Configuring basic parameters 147
- Chapter 16 151
- To configure the MBM(s) 153
- Configuring modem settings 154
- Checking for software updates 154
- Configuring voice mail 154
- Customizing security policies 154
- Performing a backup 154
- Chapter 17 155
- Chapter 18 161
- To troubleshoot the main unit 162
- To test the expansion unit 162
- To test the MBM 163
- To test a station MBM 163
- To test a trunk MBM 163
- Reset to factory settings 165
- Command Line Interface 166
- Using the Configuration CLI 167
- Using the Maintenance CLI 167
- Chapter 19 171
- To shut down the system 172
- Chapter 20 175
- Removing the power supply 176
- Connect the new power supply 176
- Chapter 21 179
- Removing the main unit 181
- Installing the new main unit 182
- To connect the cables 183
- Chapter 22 185
- To remove the MBM 186
- To insert the new MBM 187
- Chapter 23 189
- Disconnecting the cables 190
- Removing the expansion unit 190
- Removing the MBM 192
- Chapter 24 195
- Special tools 196
- Opening the main unit case 196
- To open the main unit case 197
- To remove the hard disk 199
- To remove the fan 200
- Inserting the new component 201
- To insert the new hard disk 202
- Cable routing on page 205) 204
- Figure 84 Cable routing 205
- To insert the new fan 209
- To insert the new router card 209
- Closing the main unit case 210
- Installing the main unit 211
- Connecting the cables 211
- Appendix A 213
- Table 32 BRI line numbering 214
- Appendix B 215
- Appendix C 219
- Table 34 LAN port wiring 220
- Appendix D 223
- Appendix E 225
- Appendix F 227
- Appendix G 229
- Appendix H 231
- Appendix I 233
- Appendix J 237
- Appendix K 241
- (Sheet 2 of 2) 242
- (Sheet 1 of 2) 243
- (Sheet 2 of 2) 244
- Appendix L 245
- Appendix M 249
- Appendix N 251
- Digital interfaces 252
- Tones and cadences 253
- • Reorder, 1 kHz on page 259 254
- Functionality Attribute 263
- Market profile 263
- Russia South Africa 271
- Analog Trunk parameters 276
- GASM8 parameters 282
- GASI parameters 285
- Ω 600 Ω 600 Ω 600 Ω 600 Ω 286
- ATA2 parameters 287
- ATA2 DR7 289
- Voicemail 290
- ISDN line services 293
- Trunk Types Description 295
- Numerics 297
Související produkty a manuály pro Směrovače Avaya Business Communications Manager 50
Směrovače Avaya FE1/E1 Uživatelský manuál
(24 stránky)
(24 stránky)
Směrovače Avaya BSGX4e Uživatelská příručka
(456 stránky)
(456 stránky)
Směrovače Avaya Passport ARN Routers Uživatelský manuál
(166 stránky)
(166 stránky)
Směrovače Avaya BCC Rychlý návod
(4 stránky)
(4 stránky)
Směrovače Avaya FireWall-1 Uživatelský manuál
(56 stránky)
(56 stránky)
Směrovače Avaya BSG8/12 1.0 Uživatelský manuál
(862 stránky)
(862 stránky)
Směrovače Avaya C360 Uživatelský manuál
(238 stránky)
(238 stránky)
Směrovače Avaya P460 Uživatelský manuál
(96 stránky)
(96 stránky)
Směrovače Avaya P114F Uživatelský manuál
(14 stránky)
(14 stránky)
Směrovače Avaya M15-155 Uživatelský manuál
(14 stránky)
(14 stránky)
Směrovače Avaya P460 Uživatelský manuál
(224 stránky)
(224 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.987 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce