Avaya Business Policy Switch 2000 Command Line Interface Release 2.0 Uživatelský manuál Strana 200
- Strana / 233
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
198 Chapter 6 Policy-enabled networks and QoS
212160-B
qos queue-set-assignment command
The qos queue-set-assignment command associates the 802.1p priority
values with a specific queue within a specific queue set. This association
determines the egress scheduling treatment that traffic with a specific 802.1p
priority value receives. The syntax for the
qos queue-set-assignment
command is:
qos queue-set-assignment queue-set <setid> 1p <ieee1p>
queue <qid>
The qos queue-set-assignment command is in the config command mode.
Table 115 describes the parameters and variables for the
qos
queue-set-assignment
command.
Configuring QoS filters and filter groups
You can configure filters and filter sets using the CLI. This section covers:
• “qos ip-filter command,” next
• “qos ip-filter-set command” on page 200
• “qos l2-filter command” on page 201
• “qos l2-filter-set command” on page 203
Table 115 qos queue-set-assignment command parameters and variables
Parameters
and variables
Description
queue-set
<setid>
Enter the queue set ID.
1p <ieee1p> Enter the 802.1p priority value for which the queue association is
being modified; range is between 0 and 7.
queue <qid> Enter the queue within the identified queue set to assign the 802.1p
priority traffic at egress.
- Reference for the 1
- Business Policy Switch 2000 1
- Command Line Interface 1
- Release 2.0 1
- Trademarks 2
- Restricted rights legend 2
- Statement of conditions 2
- USA requirements only 3
- European requirements only 3
- Taiwan requirements 4
- Canada requirements only 4
- Contents 7
- Chapter 3 11
- Chapter 4 11
- Chapter 5 12
- Chapter 6 13
- Appendix A 14
- About this guide 21
- Before you begin 21
- Text conventions 22
- Related publications 23
- How to get help 24
- Preface 25 25
- 26 Preface 26
- Chapter 1 27
- CLI Basics 27
- Stacking compatibility 28
- Chapter 1 CLI Basics 27 29
- New features 30
- CLI command modes 31
- 30 Chapter 1 CLI Basics 32
- Port numbering 34
- IP notation 36
- Accessing the CLI 37
- 36 Chapter 1 CLI Basics 38
- Figure 2 BPS 2000 banner 38
- Setting the CLI password 40
- Getting help 41
- Basic navigation 41
- General navigation commands 42
- Keystroke navigation 43
- Parameters 47
- BPS2000#show stack-info 51
- Chapter 1 CLI Basics 51 53
- BPS2000#show stack-oper-mode 56
- Chapter 1 CLI Basics 55 57
- 56 Chapter 1 CLI Basics 58
- Chapter 2 59
- General CLI commands 59
- Setting the terminal 60
- Configuration Filename: 65
- Setting Telnet access 73
- Setting boot parameters 77
- Setting TFTP parameters 81
- Upgrading software 84
- Observing LED indications 86
- Upgrading software images 87
- Displaying interfaces 90
- Setting SNMP parameters 92
- Setting the system event log 97
- Displaying port statistics 100
- Enabling or disabling a port 102
- Naming ports 104
- Setting port speed 105
- Enabling Autopology 109
- Enabling flow control 111
- Enabling rate-limiting 113
- Security 117
- Using MAC address security 122
- Index Mac Address 124
- _____ _________________ 124
- 1 00-60-AF-00-12-30 124
- command is: 125
- Using EAPOL-based security 130
- Using RADIUS authentication 133
- 134 Chapter 3 Security 136
- 212160-B 136
- Using MLT 150
- Using port-mirroring 153
- VLANs and IGMP 157
- 156 Chapter 5 VLANs and IGMP 158
- Parameters and 159
- Description 159
- Using IGMP snooping 172
- Displaying QoS parameters 176
- IP Filter Sets 181
- Resetting 187
- Configuring COPS 188
- Configuring QoS actions 206
- Configuring QoS meters 207
- Configuring QoS shapers 208
- Gathering QoS statistics 210
- Configuring QoS policies 211
- Reordering packets 213
- Command List 215
- 214 Appendix A Command List 216
- Appendix A Command List 215 217
- 216 Appendix A Command List 218
- Appendix A Command List 217 219
- 218 Appendix A Command List 220
- Appendix A Command List 219 221
- 220 Appendix A Command List 222
- Appendix A Command List 221 223
- 222 Appendix A Command List 224
- Appendix A Command List 223 225
- 224 Appendix A Command List 226
Související produkty a manuály pro Síťové přepínače Avaya Business Policy Switch 2000 Command Line Interface Release 2.0
Síťové přepínače Avaya L2 Průvodce konfigurací
(31 stránky)
(31 stránky)
(13 stránky)
Síťové přepínače Avaya 470/460/BPS Oznámení
(3 stránky)
(3 stránky)
Síťové přepínače Avaya BCM 2.5 Instalační manuál
(306 stránky)
(306 stránky)
Síťové přepínače Avaya Business Policy Switch 2000 Software Version 2.0 Uživatelský manuál
(334 stránky)
(334 stránky)
Síťové přepínače Avaya BayStack Operating System Switching Software (BoSS 3.1) for BayStack 460, 470 Oznámení
(86 stránky)
(86 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce