Avaya Using Technician Interface Scripts Uživatelský manuál Strana 268
- Strana / 788
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Using Technician Interface Scripts
2-216
fdl
[
ansi1
|
ansi2
|
att1
|
att2
]
Displays the Facility Data Link (FDL) error statistics in both ANSI-403 and AT&T-54016
modes.
The tables display the following information:
DS1E1 Facility Data Link (FDL) Errors (first half) — ANSI-403 mode:
ansi1 Displays only the first half of ANSI-403 mode FDL errors.
ansi2 Displays only the second half of ANSI-403 mode FDL errors.
att1 Displays only the first half of AT&T-54016 mode FDL errors.
att2 Displays only the second half of AT&T-54016 mode FDL errors.
Slot Slot identifier.
Conn Connector identifier.
CRC Counts Number of CRC-6 errors. The FDL calculates CRC-6 on the
incoming data. Each time the calculation does not match the CRC-
6 code word in the incoming enhanced super frame (ESF) data
stream, this count increments.
BPV Counts Number of bipolar (line code) violations. The FDL counts bipolar
violations whether its synchronizer is in sync or not. If the FDL is
set to receive B8ZS code words, it does not count these code words
as bipolar violations.
OOF Counts Number of out-of-frame errors. An out-of-frame error occurs
whenever two or more framing bits out of six in the Framing
Pattern Sequence (FPS) are incorrect. This event causes the FDL to
resynchronize to the incoming data stream.
FE Counts Number of individual bit errors in the FPS.
ES Counts Number of Errored Seconds (ES). An ES is any one-second time
interval with either a frame bit error or a CRC-6 error.
- Using Technician Interface 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- About This Guide 13
- Software Suites 14
- Audience 14
- Before You Begin 15
- CompuServe 16
- How to Get Help 17
- Conventions 18
- Acronyms 19
- Chapter 1 23
- Script Types 24
- Commands for Scripts 25
- Loading .bat and .mnu Scripts 27
- Setting Up Scripts 28
- Using Script Commands 30
- Using the Menu Utility 37
- Configuring Menus 40
- You can add and delete 41
- Adding a Command 42
- Deleting a Command 44
- Clearing All Commands 44
- Editing a Command 44
- Editing a Menu Title 46
- Loading a New Menu 48
- Chapter 2 53
- Using the show Command 53
- <node name> 56
- Capacity: 57
- Capabilities: 57
- <COS name> 59
- <LU name> 63
- <DLC name> 65
- <DLUS name> 68
- <PLU name> 68
- <FQCP name> 71
- <network 76
- ID>.<CP name> 76
- <mode name> 79
- <network ID>.<CP 82
- <CP name> 85
- Node Record Statistics: 86
- TG Record Statistics: 88
- <owner name> 90
- <net> 96
- <node> 96
- <circuit name> 102
- <netlow> 103
- <nethigh> 103
- <pattern> 107
- <option> 110
- command 111
- <line> 112
- <line.vpi> 113
- <line.vpi.vci> 113
- <line option> 113
- <line.circuit> 115
- <line.VPI> 117
- <line.VPI.VCI> 117
- <IP_address> 118
- <line.llindex> 125
- <line.llindex.VPI> 126
- <line.llindex.VPI.VCI> 126
- <period in seconds> 144
- <IP address> 150
- filters zone 152
- <address> 166
- <peer address> 166
- <search pattern> 166
- (not yet functioning), or Up 171
- Bootp Preferred Server 184
- MAC address> 197
- <port number> 213
- <vol> 215
- <area> 237
- <area.node> 242
- DLS Circuits 250
- 250
- command for definitions 253
- <interval number> 265
- Displays E1 port information 267
- IP address> 287
- <line.llindex.DLCI> 324
- <slot number> 334
- <slot 335
- <protocol> 357
- <service name> 384
- Sample Display – show ipx rip 386
- <name search pattern> 398
- <hex search pattern> 398
- <circuit > 408
- See “show isdn bri.” 412
- <options> 427
- Enabled or Disabled 459
- <destination sys ID> 462
- <LSID> 467
- <area-number> 470
- <line number> 476
- RxFltr1Ref Mac 479
- TxFltr1Ref Mac 479
- RxFltr2Ref Mac 479
- TxFltr2Ref Mac 479
- <circuit_name> 495
- listed under the alerts 498
- Sample Display – show ppp ip 512
- <process> 515
- <slot> 515
- <seconds> 518
- <repeat> 518
- <circuit number> 549
- <entity number> 560
- <entity name> 560
- <event number> 561
- <entity 561
- Up. You can use this 579
- circuit [ 580
- <object ID> 594
- <pool ID> 600
- ISDN Line Information: 601
- ISDN Line Information 606
- Circuit Information: 610
- Synchronous Line Information: 610
- The show telnet 643
- <VINES network address> 666
- <VINES server ID> 666
- <VINES network address 667
- Present (configured 680
- <slot.connector> 681
- Sample Display – show x25 vc 686
- Sample Display – show xb base 688
- <XNS network> 702
- <network address> 703
- <address pattern> 703
- Chapter 3 709
- Using enable/disable Commands 709
- <LS name> 711
- <port name> 712
- <circuit> 712
- <VRN name> 712
- <line_number> 714
- <circuit_number> 715
- <base> 731
- <IP_interface_address> 734
- <line.index> 737
- <area_ID> 745
- <port_number> 749
- <object_ID> 755
- <line_number.llindex> 764
- Appendix A 769
- Packet Configuration 769
- Packet Configuration 771
Související produkty a manuály pro Software Avaya Using Technician Interface Scripts
Software Avaya Read Me First: Router Software 11.02 and Site Manager 5.02 Uživatelský manuál
(10 stránky)
(10 stránky)
Software Avaya B5800 Uživatelský manuál
(70 stránky)
(70 stránky)
Software Avaya BCM 5.0 - Contact Center - Intelligent Contact Center Uživatelský manuál
(258 stránky)
(258 stránky)
Software Avaya BCM-IVR 2.1 Uživatelská příručka
(103 stránky)
(103 stránky)
Software Avaya BCM Unified Messaging Rychlý návod
(14 stránky)
(14 stránky)
Software Avaya Bay Command Console Uživatelský manuál
(130 stránky)
(130 stránky)
Software Avaya Business Communications Manager 5.0 - Configuration - Telephony Uživatelský manuál
(462 stránky)
(462 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce