Avaya (109352-E, Uživatelský manuál Strana 104
- Strana / 144
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Installing and Maintaining BN Platforms
5-8 109352-E Rev. A
When removing or installing a link module, keep the following in mind:
• If you replace a link module with another of a different type (that is, you
replace an Ethernet link module with an FDDI link module), you must first
undo the configuration of all circuits on the old slot before the hardware
platform software can properly configure the new module. Refer to
Configuring Routers (router software) or Getting Started with Site Manager
(BayStream Software) for instructions on deleting and editing a configuration
file.
• When you remove a link module, connectivity to the slot in question and the
services that slot provides become disrupted. The other routing engine
processor modules resynchronize their routing tables after the slot fails to
receive packets.
• Insert ARE link modules only in slots opposite ARE processor modules. Do
not install an ARE link module in a slot opposite a FRE or FRE-2 processor
module.
• The SRM-L and SRM-F (see next section) each supply two backbones. This
means that two backbones become inactive if you remove one of these
modules, and four backbones become inactive if you remove both. When you
insert a module, its associated backbones become active.
• Before removing or installing a link module, first access the interior of your
hardware platform. (Refer to Chapter 4, “Accessing the Interior,” for
instructions.)
The procedures for replacing the link modules and SRM-Ls are the same for the
BLN, BLN-2, and BCN. (Refer to Figure 5-3 for the BLN, Figure 5-4 for the
BLN-2, and Figure 5-5 for the BCN.)
Caution: Electrostatic discharge can damage hardware. Use the antistatic
wrist strap when handling any hardware platform components.
- Installing and Maintaining 1
- BN Platforms 1
- USA Requirements Only 3
- Bay Networks, Inc 4
- Canada Requirements Only 5
- T1 Service 8
- Bay Networks Software License 9
- (continued) 10
- Contents 11
- About This Guide 19
- <ip_address> 20
- Acronyms 21
- World Wide Web 25
- Customer Service FTP 25
- Support Source CD 26
- CompuServe 26
- InfoFACTS 27
- How to Get Help 27
- Chapter 1 29
- Backbone Link Node Overview 30
- Preparing for Installation 31
- Additional Equipment 32
- Site Requirements 33
- 1-6 109352-E Rev. A 34
- Table 1-4. BLN Dimensions 34
- Attaching Angle Brackets 35
- Installing the BLN 37
- 109352-E Rev. A 1-11 39
- Powering On the BLN 40
- LED Activation Sequence 41
- Local Connection 42
- Remote Connection 43
- (continued) 44
- Chapter 2 45
- Backbone Link Node-2 Overview 46
- 2-6 109352-E Rev. A 50
- Table 2-4. BLN-2 Dimensions 50
- 1.750" 53
- 1.4" 53
- 2-10 109352-E Rev. A 54
- Installing the BLN-2 55
- Powering On the BLN-2 57
- Chapter 3 63
- 3-2 109352-E Rev. A 64
- Shipment Contents 66
- 3-6 109352-E Rev. A 68
- 109352-E Rev. A 3-9 71
- 109352-E Rev. A 3-11 73
- Installing the BCN 74
- 109352-E Rev. A 3-15 77
- Source B power cord 78
- 109352-E Rev. A 3-19 81
- Chapter 4 85
- Accessing the Interior 85
- 4-4 109352-E Rev. A 88
- Pull Top 88
- 109352-E Rev. A 4-5 89
- 4-6 109352-E Rev. A 90
- 109352-E Rev. A 4-7 91
- 4-8 109352-E Rev. A 92
- Board Retainer Bracket 93
- (1 Screw) 93
- Air Flow 93
- BACKBONE NODE 94
- Chapter 5 97
- 5-2 109352-E Rev. A 98
- 109352-E Rev. A 5-3 99
- 109352-E Rev. A 100
- Protecting Memory Card Files 101
- Protected 102
- Unprotected 102
- 109352-E Rev. A 5-7 103
- 5-8 109352-E Rev. A 104
- 109352-E Rev. A 5-9 105
- 5-10 109352-E Rev. A 106
- 109352-E Rev. A 5-11 107
- 5-12 109352-E Rev. A 108
- 109352-E Rev. A 5-13 109
- 5-14 109352-E Rev. A 110
- B A C K B O N E N O D E 111
- Power Switch 112
- 109352-E Rev. A 5-17 113
- Replacing a Power Module 114
- 109352-E Rev. A 5-19 115
- 5-20 109352-E Rev. A 116
- 109352-E Rev. A 5-21 117
- 109352-E Rev. A 5-23 119
- 5-24 109352-E Rev. A 120
- 1. Remove the front bezel 120
- 109352-E Rev. A 5-25 121
- 5-28 109352-E Rev. A 124
- Chapter 6 125
- Switches and LEDs 125
- Reset Switch 126
- Front-Panel LEDs 126
- 620-Watt Power Module LED 127
- Power OK 128
- Appendix A 129
- Dial-Up Services Modems 129
- Adtran DSU III AR 130
- Codex 3260 131
- Codex 3261 Fast 132
- Multi-Tech Multi-Modem 133
- NEC N6450 Data Service Unit 134
- NEC N963E Plus (RS232) 135
- Telebit T3000 136
- Telebit T3000 (continued) 137
- - Tested with V.25bis only 138
- 109352-E Rev. A Index-1 139
- 109352-E Rev. A Index-3 141
- 109352-E Rev. A Index-5 143
Související produkty a manuály pro ne Avaya (109352-E,
ne Avaya 30A Uživatelský manuál
(1 stránky)
(1 stránky)
ne Avaya PSN003153u Uživatelský manuál
(2 stránky)
(2 stránky)
ne Avaya 1xx, Uživatelský manuál
(1 stránky)
(1 stránky)
ne Avaya EU24 Uživatelský manuál
(1 stránky)
(1 stránky)
(36 stránky)
(12 stránky)
ne Avaya M3900 Instalační příručka
(3 stránky)
(3 stránky)
ne Avaya BCM Networking Uživatelská příručka
(8 stránky)
(8 stránky)
ne Avaya EE Networking Uživatelský manuál
(14 stránky)
(14 stránky)
ne Avaya 1145B2 Uživatelský manuál
(1 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce