Avaya (109352-E, Uživatelský manuál Strana 113
- Strana / 144
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Hot-Swapping Hardware Components
109352-E Rev. A 5-17
3.
Swing the extractors forward to lock the board in place.
4. Observe the module and front-panel LEDs to determine whether the
FRE/FRE-2 module or SRM-F is functioning properly.
Following is a brief description of the LED activation sequence after you
insert a new FRE/FRE-2 or SRM-F module. (See the installation guide for the
module for a complete description of the LEDs.)
• When you insert a FRE/FRE-2 module, the DIAG LED turns on during
diagnostics and then turns off if diagnostics determine that the
FRE/FRE-2 is functional.
• If diagnostics determine that the FRE/FRE-2 is not functional, the DIAG
LED on the front panel and LED 8 on the FRE/FRE-2 module remain on.
If this occurs, ensure that the modules seat properly in the hardware
platform and issue the
diags command using the Bay Networks
Technician Interface.
• If diagnostics determine that the FRE/FRE-2 is functional and a link
module connects to the FRE/FRE-2, the hardware platform also performs
diagnostics on the link module.
Regardless of the results of the link module diagnostics, the BOOT LED
turns on, indicating that the FRE/FRE-2 is booting. If the link module or
any of its ports do not function, the link module Fail LED turns on.
5. Replace the board retainer bracket in a BLN or BLN-2 as follows:
a. Slide the top of the board retainer bracket into its designated ridge
and align the bottom of the bracket with the screw hole at the bottom
of the chassis (Figure 5-6 or Figure 5-7).
b. Using a screwdriver, secure the bracket to the chassis.
Note: Remove the module and repeat Steps 1 and 2 if the extractors do not
lock into place easily.
Note: Contact the Bay Networks Technical Response Center if the DIAG LED
does not turn off.
- Installing and Maintaining 1
- BN Platforms 1
- USA Requirements Only 3
- Bay Networks, Inc 4
- Canada Requirements Only 5
- T1 Service 8
- Bay Networks Software License 9
- (continued) 10
- Contents 11
- About This Guide 19
- <ip_address> 20
- Acronyms 21
- World Wide Web 25
- Customer Service FTP 25
- Support Source CD 26
- CompuServe 26
- InfoFACTS 27
- How to Get Help 27
- Chapter 1 29
- Backbone Link Node Overview 30
- Preparing for Installation 31
- Additional Equipment 32
- Site Requirements 33
- 1-6 109352-E Rev. A 34
- Table 1-4. BLN Dimensions 34
- Attaching Angle Brackets 35
- Installing the BLN 37
- 109352-E Rev. A 1-11 39
- Powering On the BLN 40
- LED Activation Sequence 41
- Local Connection 42
- Remote Connection 43
- (continued) 44
- Chapter 2 45
- Backbone Link Node-2 Overview 46
- 2-6 109352-E Rev. A 50
- Table 2-4. BLN-2 Dimensions 50
- 1.750" 53
- 1.4" 53
- 2-10 109352-E Rev. A 54
- Installing the BLN-2 55
- Powering On the BLN-2 57
- Chapter 3 63
- 3-2 109352-E Rev. A 64
- Shipment Contents 66
- 3-6 109352-E Rev. A 68
- 109352-E Rev. A 3-9 71
- 109352-E Rev. A 3-11 73
- Installing the BCN 74
- 109352-E Rev. A 3-15 77
- Source B power cord 78
- 109352-E Rev. A 3-19 81
- Chapter 4 85
- Accessing the Interior 85
- 4-4 109352-E Rev. A 88
- Pull Top 88
- 109352-E Rev. A 4-5 89
- 4-6 109352-E Rev. A 90
- 109352-E Rev. A 4-7 91
- 4-8 109352-E Rev. A 92
- Board Retainer Bracket 93
- (1 Screw) 93
- Air Flow 93
- BACKBONE NODE 94
- Chapter 5 97
- 5-2 109352-E Rev. A 98
- 109352-E Rev. A 5-3 99
- 109352-E Rev. A 100
- Protecting Memory Card Files 101
- Protected 102
- Unprotected 102
- 109352-E Rev. A 5-7 103
- 5-8 109352-E Rev. A 104
- 109352-E Rev. A 5-9 105
- 5-10 109352-E Rev. A 106
- 109352-E Rev. A 5-11 107
- 5-12 109352-E Rev. A 108
- 109352-E Rev. A 5-13 109
- 5-14 109352-E Rev. A 110
- B A C K B O N E N O D E 111
- Power Switch 112
- 109352-E Rev. A 5-17 113
- Replacing a Power Module 114
- 109352-E Rev. A 5-19 115
- 5-20 109352-E Rev. A 116
- 109352-E Rev. A 5-21 117
- 109352-E Rev. A 5-23 119
- 5-24 109352-E Rev. A 120
- 1. Remove the front bezel 120
- 109352-E Rev. A 5-25 121
- 5-28 109352-E Rev. A 124
- Chapter 6 125
- Switches and LEDs 125
- Reset Switch 126
- Front-Panel LEDs 126
- 620-Watt Power Module LED 127
- Power OK 128
- Appendix A 129
- Dial-Up Services Modems 129
- Adtran DSU III AR 130
- Codex 3260 131
- Codex 3261 Fast 132
- Multi-Tech Multi-Modem 133
- NEC N6450 Data Service Unit 134
- NEC N963E Plus (RS232) 135
- Telebit T3000 136
- Telebit T3000 (continued) 137
- - Tested with V.25bis only 138
- 109352-E Rev. A Index-1 139
- 109352-E Rev. A Index-3 141
- 109352-E Rev. A Index-5 143
Související produkty a manuály pro ne Avaya (109352-E,
ne Avaya 30A Uživatelský manuál
(1 stránky)
(1 stránky)
ne Avaya PSN003153u Uživatelský manuál
(2 stránky)
(2 stránky)
ne Avaya 1xx, Uživatelský manuál
(1 stránky)
(1 stránky)
ne Avaya EU24 Uživatelský manuál
(1 stránky)
(1 stránky)
(36 stránky)
(12 stránky)
ne Avaya M3900 Instalační příručka
(3 stránky)
(3 stránky)
ne Avaya BCM Networking Uživatelská příručka
(8 stránky)
(8 stránky)
ne Avaya EE Networking Uživatelský manuál
(14 stránky)
(14 stránky)
ne Avaya 1145B2 Uživatelský manuál
(1 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce